![]() |
| Erecting scaffolding correctly is very important for safety |
Collaborative post by another author.
When you are having work done on the outside of your house, whether that is fixing a leaking roof, repainting the fascias or repointing brickwork, a scaffold tower is often the quickest way for tradespeople to reach high spots. However, working at height carries serious risks, and falls remain the single largest cause of fatal injuries in the UK construction industry according to the Health and Safety Executive.
Even if you are not the one climbing the ladder, knowing what a safe setup looks like gives you peace of mind when builders are working around your family home and garden. These seven steps cover the proper sequence for erecting a scaffold tower safely and legally in the UK, helping you spot if corners are being cut on your property.
Understand Your Legal Duties Before You Start
UK law sets clear requirements for the safe assembly and use of scaffold towers. Under the Work at Height Regulations 2005, employers and self-employed workers must ensure that work at height is properly planned, supervised and carried out by competent people. Choosing suitable equipment is an important part of meeting these responsibilities. For example, scaffold towers for construction work provide a temporary working platform for tasks such as building maintenance, exterior repairs, and installation work. These options are particularly useful for jobs requiring workers to access different areas of a site, as towers can be repositioned on stable, level ground provided all safety precautions are followed.Anyone assembling, altering or dismantling a tower must be competent to do so. PASMA training is a widely recognised way to demonstrate competence, although UK law does not require PASMA certification specifically or impose a universal 2-metre threshold for tower assembly.
You'll also need a suitable risk assessment before work begins. That assessment should identify overhead hazards, ground conditions, proximity to power lines, and the intended working load. It shouldn't be left to be completed afterwards, but done in advance to guide every decision made during assembly and use.
If you're hiring the tower, confirm that it meets the relevant safety standards and has been properly maintained and inspected. A reputable supplier should be able to provide information about the equipment's condition specifications, and safe assembly requirements.
Inspect the Equipment and Gather the Right Components
Components should be checked carefully before assembly starts. Every piece needs carefully, including frames, braces, deck boards, toe boards, guardrails and base plates. Look for cracks, bent tubing, corroded pins, missing spigots or damaged casters. One faulty component can bring the whole structure into question.Parts from different manufacturers shouldn't be mixed. Tower components are engineered to work together as a unified system, and mixing them can create gaps in the platform, misaligned locking pins or unstable connections. If a component doesn't match, it needs replacing before work begins.
The manufacturer's instruction manual should also be checked. Different tower models, whether aluminium, GRP, folding, or stair access, have different assembly sequences. The manual is specific to each model so general knowledge alone isn't enough.
Prepare the Ground and Position the Base
The tower base must sit on firm, level ground that can support the total load. Soft ground, lawn edges, camber, debris or drainage grates under a base plate create instability. Always use the manufacturer's base plates rather than timber offcuts or improvised packers, and if the ground is uneven, use adjustable legs to compensate if the patio or driveway is uneven.The tower should be positioned so the access ladder faces away from the direction of the main work activity. This keeps the working face clear and reduces the chance of people leaning across the platform to reach something behind them.
Check that the tower's footprint won't obstruct your driveway, garden paths, back door or areas where your children play. If it sits near a shared walkway physical barriers and clear signage should be put in place as outlined in the risk assessment.
Erect the First Lift Correctly
Assembly starts by fitting the castors or base plates to the bottom frames. If castors are used, all four brakes must be locked before building any section above them, as unlocked castors are a frequent cause of collapse during assembly. The two base frames slot together with a horizontal brace at the bottom and one at the top of the first lift, following the manufacturer's sequence for that specific tower model.The diagonal braces go on next. They give the structure its rigidity and without them, the tower will sway under load. Each brace must click or pin securely so the locking mechanism is properly engaged.
Workers shouldn't stand on the platform of the first lift to build the second, using a hop-up or step at ground level instead. Climbing a half-built frame and reaching up is one of the most common mistakes made during assembly.
Build the Upper Lifts and Fit the Working Platform
Each upper lift is added by slotting frames onto the spigots of the lift below. Diagonal braces are fitted as each section goes up rather than building two lifts before bracing the first. Platform boards slot into place once a lift is fully braced.The working platform must be close-boarded with no gaps wider than 25mm. Anything beyond that creates a trip hazard and puts people below at risk from falling tools or debris. Trap boards or proprietary deck panels that clip into place are far safer than loose boards, which can shift underfoot.
An access hatch platform should be fitted if the tower has one. On towers without a hatch, your only safe access option is an internal ladder inside the tower frame. Nobody should climb the outside of the structure.
Installing Guardrails, Toe Boards and Stabilisers
At every working platform level, a main guardrail must be fitted between 950 mm and 1,150 mm above the platform surface and an intermediate guardrail at mid-height. The toe board must be at least 150mm high and run the full perimeter of the platform. These are legal requirements under the Work at Height Regulations 2005 and the PASMA Code of Practice requires them.Stabilisers or outriggers must be fitted in accordance with the manufacturer's instructions for the specific tower height and base width. They need to be fitted to all four sides with the rubber feet making firm, even contact with the ground.
Stabilisers don't replace proper base setup. If the ground has shifted or a castor was left unlocked, outriggers might slow a collapse but they wont prevent it.
Inspection, Tagging and Maintenance of the Tower During Use
Before anyone works on the tower, a formal pre-use inspection should be completed. This means walking around the base to confirm that all braces are engaged, casters are locked, guardrails are at the correct heights and toe boards are secure, alongside checking the platform boards for any signs of damage or movement.A Scafftag or equivalent inspection tag should be attached at the point of access showing the date of inspection, the inspector's name and the maximum safe working load. Anyone approaching the tower needs to see at a glance whether it's safe to use. If the tag's missing or out of date, the tower should go out of service until it's been properly inspected.
The tower should be re-inspected after any significant bad weather (eg heavy rain or winds) or after any impact or modification to the frame. It shouldn't be assumed that because the tower was fine yesterday it's fine today. It should also never be moved with anyone on it. If a tower is being left up overnight in your garden, double checking that the castors are locked and no loose tools or ladders are left accessible helps keep curious children safe once the tradespeople head home for the day.











No comments
Thanks for your comment (unless it is spam in which case, why?)